| | Set Attribute <attrib_type> Auto {actuate|update} {on|off}
|
| | [Set] Auto Size Default
|
| | [Set] Auto Size Function [1|2]
|
| | Set AutoUniqueId {on|OFF}
|
| | Set Auto Sweep Scheme {Sw|Proj|Trans|Rot}
|
| | Set Boolean Regularize [ON|off]
|
| | Set Block Mixed Element Output {offset|degenerate|explicit}
|
| | Set Block Triangle Offset <value>
|
| | Set Block Tetrahedron Offset <value>
|
| | Set Block Pyramid Offset <value>
|
| | Set Catch Interrupt [on|off]
|
| | Set Cleanup Angle <val> (default = 179.0)
|
| | Set {curve|surface} Imprint Cleanup Tolerance <value>
|
| | Set Continue Meshing [ON|off]
|
| | Set Core [on|off]
|
| | Set {Corner|End} Angle <degrees>
|
| | set Corner Weight <value>
|
| | Set Crash Save [on|off]
|
| | [set] Diagnostic {on|off}
|
| | [Set] Geometry Version <version> Supported versions: (106, 107, 201, 300, 301, 401, 402, 403, 500, 501, 502, 503, 600, 601, 602, 603, 700, 701, 702, 703, 704, 705, 800, 1007, 1100, 1200, 1300, 1400, 1500, 1600, 1700, 1800, 1900, 2100, 2200, 2401)
|
| | [set] Debug <index> {on|off}
|
| | [set] Debug <index> File <’filename’>
|
| | [set] Debug <index> Terminal
|
| | set Default Blocks {on|off|Volumes|Surfaces}
|
| | set Default Names {on|off}
|
| | Set Default Element [tri|tet|QUAD|HEX|None]
|
| | Set Default Autosize [ON|off]
|
| | Set Digits [<number_to_list = -1>]
|
| | Set Deletion Off
|
| | Set Developer [commands] [on|off]
|
| | Set Detail Periodic Fraction <value>
|
| | Set Duplicate Block Elements {on|OFF}
|
| | [set] Echo [on|off]
|
| | Set Exodus Single Precision [on|off]
|
| | [Set] [Export Mesh] Nodeset Associativity [on|off]
|
| | [Set] [Export Mesh] Nodeset Associativity Complete [on|off]
|
| | [Set] Facet BBox [ON|off]
|
| | [Set] Facet_modify [ON|off]
|
| | Set Fastq [on|off]
|
| | Set File Overwrite [Check] [ON|off]
|
| | Set FPE {divbyzero|invalid|underflow|overflow|all} [<toggle>]
|
| | set Fix Duplicate Names {on|off}
|
| | set FullHex [Use] [on|off]
|
| | [Set] Geometry Accuracy <value>
|
| | Set Geometry Engine {ACIS|catia|facet}
|
| | Set Group Edge Visibility [on|off]
|
| | Set Hex Relative Size Metric <value>
|
| | [Set] Info {on|off}
|
| | Set Interval Weight <value>
|
| | Set Import Mesh [vertex] [curve] [surface] Tolerance <distance>
|
| | [Set] Import Mesh NodeSet Associativity [ON|off]
|
| | Set Import Mesh NodeSet Order [On|off]
|
| | Set Imprint Groups {ON|off}
|
| | Set Keep Invalid Mesh [on|off]
|
| | [set] Journal {on|off}
|
| | [set] Journal [Graphics|Names|Aprepro|Errors] [on|off]
|
| | [set] Journal idless [on|off|reverse]
|
| | set Keep Invalid Mesh {on|off}
|
| | [Set] Laminate Tolerance <double>
|
| | Set Large Angle Weight <value>
|
| | Set Large Exodus [On|off]
|
| | [Set] Logging {off|on file <’filename’> [resume]}
|
| | [Set] Logging Errors {off|on file <’filename’> [resume]}
|
| | Set Mapping Constraint [ON|off]
|
| | set Match Intervals Rounding {on|off}
|
| | set Match Intervals Fast {on|off}
|
| | Set Match Intervals Delta <interval_difference = 0.0>
|
| | Set Maximum Arc_span {<angle>|default}
|
| | Set Maximum Interval <int>
|
| | Set Maximum Memory [on|off|value(in MB)]
|
| | Set Merge Test BBox {on|off}
|
| | Set Merge Test InternalSurf {on|OFF|Spline}
|
| | Set Merge Base Names [on|off]
|
| | Set Measure Small Tolerance <value>
|
| | Set Metrics [on|off]
|
| | Set Mesh Autodelete [ON|off]
|
| | [Set] Morph Smooth [ON|off]
|
| | Set Multisweep [ON|off]
|
| | Set Nastran Exporter Params Add ’<param_string>’
|
| | Set Nastran Exporter Params Remove ’<param_string>’
|
| | Set Nastran Exporter Params Clear
|
| | Set New Ids [on|off] Set Node Coincident Tolerance [<value>]
|
| | set Node Constraint [ON|off]
|
| | Set Overlap [Facet] {Angle|Absolute} <value>
|
| | Set Overlap {Minimum|Maximum} {Gap|Angle} <value>
|
| | Set Overlap Normal {ANY|opposite|same}
|
| | Set Overlap Tolerance <value>
|
| | Set Overlap Group {on|off}
|
| | Set Overlap {List|Display} {ON|off}
|
| | Set Overlap [Within] {Body|Volume} {on|off}
|
| | Set Overlap Imprnt {on|off}
|
| | Set Parallel Meshing [on|off]
|
| | [Set] Paver Cleanup {ON|off|extend}
|
| | [Set] Paver Diagonal Scale <factor> (default = 0.9)
|
| | [Set] Paver Grid Cell <factor> (default = 2.5)
|
| | [Set] Paver Size Limits {default|minimum <value>|maximum<value>}
|
| | [set] Paver Smooth Method { Default | Smooth Scheme|Old}
|
| | [set] Paver Linearsizing {off|on}
|
| | Set Persistent Ids {off|ON}
|
| | Set Patran Export Autogroups [on|off]
|
| | Set Patran Export Groups [ON|off]
|
| | Set Play History {on|off}
|
| | [Set] Project Smooth {on|off}
|
| | Set Push Attribs {on|off}
|
| | Set Print Quality {WARNING|error|off}
|
| | Set QTri Test {angle|diagonal}
|
| | Set Qtri Split <2|4> (default = 2)
|
| | Set Quad Relative Size Metric <value>
|
| | Set Quality Threshold <double> (default = 0.2)
|
| | set Replacement character ’.|_|@’
|
| | Set ReverseZoom [on|off]
|
| | Set Save [Exodus|Cubit] [backups <number>]
|
| | [Set] Scheme Auto Fuzzy [Tolerance] <degrees>
|
| | Set Separate After Webcut [ON|off]
|
| | [Set] Smooth Method {laplacian | isoparametric}
|
| | [set] Smooth Tol <value> (Default = 0.05)
|
| | Set {source|target} surface pattern ’<pattern>’
|
| | Set Split Surface Tolerance <value>
|
| | Set Split Surface Parametric {on|off}
|
| | Set Split Surface Auto Detect Triange {ON|off}
|
| | Set Split Surface Point Angle Threshold <value>
|
| | Set Split Surface Side Angle Threshold <value>
|
| | Set Split Surface Extend Gap Threshold <value>
|
| | Set Split Surface Extend Tolerance <value>
|
| | Set Split Surface Extend Normal {on|OFF}
|
| | Set Stop Error {on|OFF}
|
| | Set Submap CornerPicking {ON|off}
|
| | set Suffix character ’.|_|@’
|
| | Set Tight [[Bounding] [Box] [{Surface|Curve|Vertex} {on|off}]]
|
| | [Set] Tridelaunay Point Placement [{asp|gq}] (Advancing Steiner Point, Guaranteed Quality)
|
| | [Set] Trimesher Advancing Front
|
| | [Set] Tolerant Mesh Feature Size <value>
|
| | [Set] Tolerant Mesh MBG {OFF|on|only}
|
| | Set Tri Relative Size Metric <value>
|
| | Set Tet Relative Size Metric <value>
|
| | Set Turn Weight <value>
|
| | Set Unite Mixed [ON|off]
|
| | [Set] Unmerge Duplicate_mesh {on|off}
|
| | [Set] Unmerge New Ids [{on|off}]
|
| | Set Verbose Errors [on|off]
|
| | Set Verbose Mesh [on|off]
|
| | [Set] Warning {on|off}
|
| | Set WorkingDirectory ’directory_path’
|