reset ########## Inserted Commands ############## ########## new volume for creating a hole ############## create Cylinder height 100 radius 1 ######################################################## import acis "yoke_male.sat" attributes_on separate_bodies ########## Inserted Commands ############## ########## position the volume for creating the hole ######################### vol 1 rotate 90 about x vol 1 move 0 50 0 sub 1 from 2 ############################################################################## ########### do the rest of the commands from the orginal file ################ # remove some extraneous curves on the small rounds regularize volume all # remove the small rounds remove surface ( at -11.7775 25.8554 10.8195 ordinal 1 at -9.29066 14.605 10.3943 ordinal 1 at 0 1.59615 10.8797 ordinal 1 at 9.29066 14.605 10.3943 ordinal 1 at 11.7775 25.8554 10.8195 ordinal 1 at 11.7775 25.8554 -10.8195 ordinal 1 at 9.29066 14.605 -10.3943 ordinal 1 at 0 1.59615 -10.8797 ordinal 1 at -9.29066 14.605 -10.3943 ordinal 1 at -11.7775 25.8554 -10.8195 ordinal 1 ordered ) extend # decompose for hex meshing webcut volume ( at -0.0114257 33.1611 0 ordinal 1 ordered ) with sheet extended from surface ( at -6.25189e-011 14.5726 10.16 ordinal 1 ordered ) webcut volume ( at -0.0114257 33.1611 -4.945 ordinal 1 ordered ) with sheet extended from surface ( at 6.25207e-011 14.5726 -10.16 ordinal 1 ordered ) webcut volume ( at -0.0114257 47.7337 0 ordinal 1 ordered ) sweep surface ( at 18.4948 29.1938 -3.55271e-015 ordinal 1 ordered ) vector 0 1 0 through_all webcut volume ( at -1.06597 47.7337 0 ordinal 1 ordered ) sweep surface ( at -18.5062 29.1945 -3.55271e-015 ordinal 1 ordered ) vector 0 1 0 through_all webcut volume ( at -6.41745e-006 23.3125 15.1048 ordinal 1 at 6.41745e-006 23.3125 -15.1048 ordinal 1 ordered ) with plane xplane offset 12 noimprint nomerge webcut volume ( at -2.05725 23.3125 15.1048 ordinal 1 at -2.05724 23.3125 -15.1048 ordinal 1 ordered ) with plane xplane offset -12 noimprint nomerge imprint all merge all # do some custom settings on volume 1 to get it to mesh volume ( at 2.12179e-008 48.2337 -8.88178e-016 ordinal 1 ordered ) redistribute nodes off volume ( at 2.12179e-008 48.2337 -8.88178e-016 ordinal 1 ordered ) scheme sweep source surface ( at 2.12179e-008 47.625 0 ordinal 1 at 5.55625 53.975 8.88178e-016 ordinal 1 at -1.60925 68.1421 -9.85381e-017 ordinal 1 at 0 66.675 0 ordinal 1 ordered ) target surface ( at -1.77636e-015 29.1452 0 ordinal 1 ordered ) sweep_smooth auto sweep_transform least_squares autosmooth_target off mesh volume all smooth surface all smooth volume ( at 2.12179e-008 48.2337 -8.88178e-016 ordinal 1 ordered )